# Solution Manual For Fundamentals of Thermal-Fluid Sciences, 5th Edition

Preview Extract

2-1
Solutions Manual
for
Fundamentals of Thermal Fluid Sciences
5th Edition
Yunus A. รengel, John M. Cimbala, Robert H. Turner
McGraw-Hill, 2017
Chapter 2
BASIC CONCEPTS OF THERMODYNAMICS
PROPRIETARY AND CONFIDENTIAL
This Manual is the proprietary property of McGraw-Hill Education and protected by copyright and
other state and federal laws. By opening and using this Manual the user agrees to the following
restrictions, and if the recipient does not agree to these restrictions, the Manual should be promptly
returned unopened to McGraw-Hill Education: This Manual is being provided only to authorized
professors and instructors for use in preparing for the classes using the affiliated textbook. No
other use or distribution of this Manual is permitted. This Manual may not be sold and may not
be distributed to or used by any student or other third party. No part of this Manual may be
reproduced, displayed or distributed in any form or by any means, electronic or otherwise,
without the prior written permission of McGraw-Hill Education.
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-2
Systems, Properties, State, and Processes
2-1C The radiator should be analyzed as an open system since mass is crossing the boundaries of the system.
2-2C The system is taken as the air contained in the piston-cylinder device. This system is a closed or fixed mass system
since no mass enters or leaves it.
2-3C A can of soft drink should be analyzed as a closed system since no mass is crossing the boundaries of the system.
2-4C Intensive properties do not depend on the size (extent) of the system but extensive properties do.
2-5C If we were to divide the system into smaller portions, the weight of each portion would also be smaller. Hence, the
weight is an extensive property.
2-6C Yes, because temperature and pressure are two independent properties and the air in an isolated room is a simple
compressible system.
2-7C If we were to divide this system in half, both the volume and the number of moles contained in each half would be
one-half that of the original system. The molar specific volume of the original system is
v ๏ฝ
V
N
and the molar specific volume of one of the smaller systems is
V/ 2 V
๏ฝ
N /2 N
which is the same as that of the original system. The molar specific volume is then an intensive property.
v ๏ฝ
2-8C A process during which a system remains almost in equilibrium at all times is called a quasi-equilibrium process.
Many engineering processes can be approximated as being quasi-equilibrium. The work output of a device is maximum and
the work input to a device is minimum when quasi-equilibrium processes are used instead of nonquasi-equilibrium
processes.
2-9C A process during which the temperature remains constant is called isothermal; a process during which the pressure
remains constant is called isobaric; and a process during which the volume remains constant is called isochoric.
2-10C The pressure and temperature of the water are normally used to describe the state. Chemical composition, surface
tension coefficient, and other properties may be required in some cases.
As the water cools, its pressure remains fixed. This cooling process is then an isobaric process.
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-3
2-11C When analyzing the acceleration of gases as they flow through a nozzle, the proper choice for the system is the
volume within the nozzle, bounded by the entire inner surface of the nozzle and the inlet and outlet cross-sections. This is a
control volume since mass crosses the boundary.
2-12C The specific gravity, or relative density, and is defined as the ratio of the density of a substance to the density of
some standard substance at a specified temperature (usually water at 4ยฐC, for which ๏ฒH2O = 1000 kg/m3). That is,
SG ๏ฝ ๏ฒ / ๏ฒ H2O . When specific gravity is known, density is determined from ๏ฒ ๏ฝ SG ๏ด ๏ฒ H2O .
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-4
2-13
The variation of density of atmospheric air with elevation is given in tabular form. A relation for the variation of
density with elevation is to be obtained, the density at 7 km elevation is to be calculated, and the mass of the atmosphere
using the correlation is to be estimated.
Assumptions 1 Atmospheric air behaves as an ideal gas. 2 The earth is perfectly sphere with a radius of 6377 km, and the
thickness of the atmosphere is 25 km.
Properties The density data are given in tabular form as
z, km
0
1
2
3
4
5
6
8
10
15
20
25
r, km
6377
6378
6379
6380
6381
6382
6383
6385
6387
6392
6397
6402
๏ฒ, kg/m3
1.225
1.112
1.007
0.9093
0.8194
0.7364
0.6601
0.5258
0.4135
0.1948
0.08891
0.04008
Analysis Using EES, (1) Define a trivial function rho= a+z in equation window, (2) select new parametric table from
Tables, and type the data in a two-column table, (3) select Plot and plot the data, and (4) select plot and click on โcurve fitโ
to get curve fit window. Then specify 2nd order polynomial and enter/edit equation. The results are:
๏ฒ(z) = a + bz + cz2 = 1.20252 โ 0.101674z + 0.0022375z2
for the unit of kg/m3,
(or, ๏ฒ(z) = (1.20252 โ 0.101674z + 0.0022375z2)๏ด109 for the unit of kg/km3)
where z is the vertical distance from the earth surface at sea level. At z = 7 km, the equation would give ๏ฒ = 0.60 kg/m3.
(b) The mass of atmosphere can be evaluated by integration to be
m๏ฝ
๏ฒ
๏ฒdV ๏ฝ
V
๏
๏ฒ
h
z ๏ฝ0
(a ๏ซ bz ๏ซ cz 2 )4๏ฐ (r0 ๏ซ z ) 2 dz ๏ฝ 4๏ฐ
๏ฒ
h
z ๏ฝ0
(a ๏ซ bz ๏ซ cz 2 )(r02 ๏ซ 2r0 z ๏ซ z 2 )dz
๏
๏ฝ 4๏ฐ ar02 h ๏ซ r0 (2a ๏ซ br0 )h 2 / 2 ๏ซ (a ๏ซ 2br0 ๏ซ cr02 )h 3 / 3 ๏ซ (b ๏ซ 2cr0 )h 4 / 4 ๏ซ ch 5 / 5
where r0 = 6377 km is the radius of the earth, h = 25 km is the thickness of the atmosphere, and a = 1.20252, b = 0.101674, and c = 0.0022375 are the constants in the density function. Substituting and multiplying by the factor 10 9 for the
density unity kg/km3, the mass of the atmosphere is determined to be
m = 5.092๏ด1018 kg
Discussion Performing the analysis with excel would yield exactly the same results.
EES Solution for final result:
a=1.2025166;
b=-0.10167
c=0.0022375;
r=6377;
h=25
m=4*pi*(a*r^2*h+r*(2*a+b*r)*h^2/2+(a+2*b*r+c*r^2)*h^3/3+(b+2*c*r)*h^4/4+c*h^5/5)*1E+9
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-5
Temperature
2-14C They are Celsius (๏ฐC) and kelvin (K) in the SI, and fahrenheit (๏ฐF) and rankine (R) in the English system.
2-15C Probably, but not necessarily. The operation of these two thermometers is based on the thermal expansion of a fluid.
If the thermal expansion coefficients of both fluids vary linearly with temperature, then both fluids will expand at the same
rate with temperature, and both thermometers will always give identical readings. Otherwise, the two readings may deviate.
2-16C Two systems having different temperatures and energy contents are brought in contact. The direction of heat transfer
is to be determined.
Analysis Heat transfer occurs from warmer to cooler objects. Therefore, heat will be transferred from system B to system A
until both systems reach the same temperature.
2-17 A temperature is given in ๏ฐC. It is to be expressed in K.
Analysis The Kelvin scale is related to Celsius scale by
T(K] = T(๏ฐC) + 273
Thus,
T(K] = 37๏ฐC + 273 = 310 K
2-18E The temperature of air given in ๏ฐC unit is to be converted to ๏ฐF and R unit.
Analysis Using the conversion relations between the various temperature scales,
T (๏ฐF) ๏ฝ 1.8T (๏ฐC) ๏ซ 32 ๏ฝ (1.8)(150) ๏ซ 32 ๏ฝ 302 ๏ฐF
T (R ) ๏ฝ T (๏ฐF) ๏ซ 460 ๏ฝ 302 ๏ซ 460 ๏ฝ 762 R
2-19 A temperature change is given in ๏ฐC. It is to be expressed in K.
Analysis This problem deals with temperature changes, which are identical in Kelvin and Celsius scales. Thus,
๏T(K] = ๏T(๏ฐC) = 70 K
2-20E The flash point temperature of engine oil given in ๏ฐF unit is to be converted to K and R units.
Analysis Using the conversion relations between the various temperature scales,
T (R ) ๏ฝ T (๏ฐF) ๏ซ 460 ๏ฝ 363 ๏ซ 460 ๏ฝ 823 R
T (K ) ๏ฝ
T (R ) 823
๏ฝ
๏ฝ 457 K
1.8
1.8
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-6
2-21E The temperature of ambient air given in ๏ฐC unit is to be converted to ๏ฐF, K and R units.
Analysis Using the conversion relations between the various temperature scales,
T ๏ฝ ๏ญ40๏ฐC ๏ฝ (๏ญ40)(1.8) ๏ซ 32 ๏ฝ ๏ญ40 ๏ฐF
T ๏ฝ ๏ญ40 ๏ซ 273.15 ๏ฝ 233.15 K
T ๏ฝ ๏ญ40 ๏ซ 459.67 ๏ฝ 419.67 R
2-22E A temperature change is given in ๏ฐF. It is to be expressed in ๏ฐC, K, and R.
Analysis This problem deals with temperature changes, which are identical in Rankine and Fahrenheit scales. Thus,
๏T(R) = ๏T(ยฐF) = 45 R
The temperature changes in Celsius and Kelvin scales are also identical, and are related to the changes in Fahrenheit and
Rankine scales by
๏T(K) = ๏T(R)/1.8 = 45/1.8 = 25 K
and
๏T(๏ฐC) = ๏T(K) = 25๏ฐC
Pressure, Manometer, and Barometer
2-23C The atmospheric pressure, which is the external pressure exerted on the skin, decreases with increasing elevation.
Therefore, the pressure is lower at higher elevations. As a result, the difference between the blood pressure in the veins and
the air pressure outside increases. This pressure imbalance may cause some thin-walled veins such as the ones in the nose to
burst, causing bleeding. The shortness of breath is caused by the lower air density at higher elevations, and thus lower
amount of oxygen per unit volume.
2-24C The blood vessels are more restricted when the arm is parallel to the body than when the arm is perpendicular to the
body. For a constant volume of blood to be discharged by the heart, the blood pressure must increase to overcome the
increased resistance to flow.
2-25C No, the absolute pressure in a liquid of constant density does not double when the depth is doubled. It is the gage
pressure that doubles when the depth is doubled.
2-26C Pascalโs principle states that the pressure applied to a confined fluid increases the pressure throughout by the same
amount. This is a consequence of the pressure in a fluid remaining constant in the horizontal direction. An example of
Pascalโs principle is the operation of the hydraulic car jack.
2-27C The density of air at sea level is higher than the density of air on top of a high mountain. Therefore, the volume flow
rates of the two fans running at identical speeds will be the same, but the mass flow rate of the fan at sea level will be
higher.
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-7
2-28 The pressure in a vacuum chamber is measured by a vacuum gage. The absolute pressure in the chamber is to be
determined.
Analysis The absolute pressure in the chamber is determined from
Pabs ๏ฝ Patm ๏ญ Pvac ๏ฝ 92 ๏ญ 35 ๏ฝ 57 kPa
35 kPa
Pabs
Patm = 92 kPa
2-29 The pressure in a tank is given. The tank’s pressure in various units are to be determined.
Analysis Using appropriate conversion factors, we obtain
(a)
๏ฆ 1 kN/m 2 ๏ถ
๏ท ๏ฝ 1200 kN/m 2
P ๏ฝ (1200 kPa )๏ง
๏ง 1 kPa ๏ท
๏จ
๏ธ
(b)
๏ฆ 1 kN/m 2 ๏ถ๏ฆ 1000 kg ๏ m/s 2 ๏ถ
๏ท ๏ฝ 1,200,000 kg/m ๏ s 2
๏ท๏ง
P ๏ฝ (1200 kPa )๏ง
๏ง 1 kPa ๏ท๏ง
๏ท
1
kN
๏จ
๏ธ๏จ
๏ธ
(c)
๏ฆ 1 kN/m 2 ๏ถ๏ฆ 1000 kg ๏ m/s 2 ๏ถ๏ฆ 1000 m ๏ถ
2
๏ท๏ง
๏ท๏ง
P ๏ฝ (1200 kPa )๏ง
๏ท ๏ฝ 1,200,000, 000 kg/km ๏ s
๏ง 1 kPa ๏ท๏ง
๏ท
1 kN
๏จ
๏ธ๏จ
๏ธ๏จ 1 km ๏ธ
2-30E The pressure in a tank in SI unit is given. The tank’s pressure in various English units are to be determined.
Analysis Using appropriate conversion factors, we obtain
(a)
๏ฆ 20.886 lbf/ft 2 ๏ถ
๏ท ๏ฝ 31,330 lbf/ft 2
P ๏ฝ (1500 kPa )๏ง
๏ง
๏ท
1
kPa
๏จ
๏ธ
(b)
๏ฆ 20.886 lbf/ft 2 ๏ถ๏ฆ 1 ft 2 ๏ถ๏ฆ 1 psia ๏ถ
๏ท๏ง
๏ท
P ๏ฝ (1500 kPa )๏ง
๏ฝ 217.6 psia
๏ง
๏ท๏ง 144 in 2 ๏ท๏ง๏จ 1 lbf/in 2 ๏ท๏ธ
1
kPa
๏จ
๏ธ๏จ
๏ธ
2-31E The pressure given in mm Hg unit is to be converted to psia.
Analysis Using the mm Hg to kPa and kPa to psia units conversion factors,
๏ฆ 0.1333 kPa ๏ถ๏ฆ 1 psia ๏ถ
๏ท๏ท๏ง
P ๏ฝ (1500 mm Hg )๏ง๏ง
๏ท ๏ฝ 29.0 psia
๏จ 1 mm Hg ๏ธ๏จ 6.895 kPa ๏ธ
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-8
2-32E The pressure in a tank is measured with a manometer by measuring the differential height of the manometer fluid.
The absolute pressure in the tank is to be determined for the cases of the manometer arm with the higher and lower fluid
level being attached to the tank .
Assumptions The fluid in the manometer is incompressible.
Properties The specific gravity of the fluid is given to be SG = 1.25. The
density of water at 32๏ฐF is 62.4 lbm/ft3 (Table A-3E)
Analysis The density of the fluid is obtained by multiplying its specific
Air
gravity by the density of water,
28 in
๏ฒ ๏ฝ SG ๏ด ๏ฒ H 2O ๏ฝ (1.25)(62.4 lbm/ft 3 ) ๏ฝ 78.0 lbm/ft 3
SG = 1.25
The pressure difference corresponding to a differential height of 28 in
between the two arms of the manometer is
Patm = 12.7 psia
๏ฆ
๏ถ๏ฆ 1ft 2 ๏ถ
1 lbf
๏ท ๏ฝ 1.26 psia
๏ท๏ง
๏P ๏ฝ ๏ฒgh ๏ฝ (78 lbm/ft )(32.174ft/s )(28/12ft)๏ง๏ง
2 ๏ท๏ง
2๏ท
32.174
lbm
๏
ft/s
144
in
๏จ
๏ธ๏จ
๏ธ
3
2
Then the absolute pressures in the tank for the two cases become:
(a) The fluid level in the arm attached to the tank is higher (vacuum):
Pabs ๏ฝ Patm ๏ญ Pvac ๏ฝ 12.7 ๏ญ 1.26 ๏ฝ 11.44 psia
(b) The fluid level in the arm attached to the tank is lower:
Pabs ๏ฝ Pgage ๏ซ Patm ๏ฝ 12.7 ๏ซ 1.26 ๏ฝ 13.96 psia
Discussion Note that we can determine whether the pressure in a tank is above or below atmospheric pressure by simply
observing the side of the manometer arm with the higher fluid level.
2-33 The pressure in a pressurized water tank is measured by a multi-fluid manometer. The gage pressure of air in the tank
is to be determined.
Assumptions The air pressure in the tank is uniform (i.e., its variation with elevation is negligible due to its low density),
and thus we can determine the pressure at the air-water interface.
Properties The densities of mercury, water, and oil are given to be 13,600, 1000, and 850 kg/m3, respectively.
Analysis Starting with the pressure at point 1 at the air-water interface, and moving along the tube by adding (as we go
down) or subtracting (as we go up) the ๏ฒgh terms until we reach point 2, and setting the result equal to Patm since the tube
is open to the atmosphere gives
P1 ๏ซ ๏ฒ water gh1 ๏ซ ๏ฒ oil gh2 ๏ญ ๏ฒ mercury gh3 ๏ฝ Patm
Solving for P1,
P1 ๏ฝ Patm ๏ญ ๏ฒ water gh1 ๏ญ ๏ฒ oil gh2 ๏ซ ๏ฒ mercury gh3
or,
P1 ๏ญ Patm ๏ฝ g ( ๏ฒ mercury h3 ๏ญ ๏ฒ water h1 ๏ญ ๏ฒ oil h2 )
Noting that P1,gage = P1 – Patm and substituting,
P1,gage ๏ฝ (9.81 m/s 2 )[(13,600 kg/m 3 )(0.4 m) ๏ญ (1000 kg/m 3 )(0.2 m)
๏ฆ
๏ถ๏ฆ 1 kPa ๏ถ
1N
๏ท
๏ญ (850 kg/m 3 )(0.3 m)]๏ง
๏ง 1 kg ๏ m/s 2 ๏ท๏ง๏จ 1000 N/m 2 ๏ท๏ธ
๏จ
๏ธ
๏ฝ 48.9 kPa
Discussion Note that jumping horizontally from one tube to the next and realizing that pressure remains the same in the
same fluid simplifies the analysis greatly.
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-9
2-34 The barometric reading at a location is given in height of mercury column. The atmospheric pressure is to be
determined.
Properties The density of mercury is given to be 13,600 kg/m3.
Analysis The atmospheric pressure is determined directly from
Patm ๏ฝ ๏ฒgh
๏ฆ 1N
๏ถ๏ฆ 1 kPa ๏ถ
๏ท
๏ฝ (13,600 kg/m 3 )(9.81 m/s 2 )(0.750 m)๏ง
๏ง 1 kg ๏ m/s 2 ๏ท๏ง๏จ 1000 N/m 2 ๏ท๏ธ
๏จ
๏ธ
๏ฝ 100.1 kPa
2-35E The weight and the foot imprint area of a person are given. The pressures this man exerts on the ground when he
stands on one and on both feet are to be determined.
Assumptions The weight of the person is distributed uniformly on foot imprint area.
Analysis The weight of the man is given to be 200 lbf. Noting that pressure is force per unit
area, the pressure this man exerts on the ground is
(a) On both feet:
P๏ฝ
W
200 lbf
๏ฝ
๏ฝ 2.78 lbf/in 2 ๏ฝ 2.78 psi
2 A 2 ๏ด 36 in 2
(b) On one foot:
P๏ฝ
W 200 lbf
๏ฝ
๏ฝ 5.56 lbf/in 2 ๏ฝ 5.56 psi
A 36 in 2
Discussion Note that the pressure exerted on the ground (and on the feet) is reduced by half
when the person stands on both feet.
2-36 The gage pressure in a liquid at a certain depth is given. The gage pressure in the same liquid at a different depth is to
be determined.
Assumptions The variation of the density of the liquid with depth is negligible.
Analysis The gage pressure at two different depths of a liquid can be expressed as
P1 ๏ฝ ๏ฒgh1
and
P2 ๏ฝ ๏ฒgh2
Taking their ratio,
P2 ๏ฒgh2 h2
๏ฝ
๏ฝ
P1
๏ฒgh1 h1
h1
1
h2
Solving for P2 and substituting gives
P2 ๏ฝ
h2
9m
P1 ๏ฝ
(42 kPa) ๏ฝ 126 kPa
h1
3m
2
Discussion Note that the gage pressure in a given fluid is proportional to depth.
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-10
2-37 The absolute pressure in water at a specified depth is given. The local atmospheric pressure and the absolute pressure
at the same depth in a different liquid are to be determined.
Assumptions The liquid and water are incompressible.
Properties The specific gravity of the fluid is given to be SG = 0.85. We take the density of water to be 1000 kg/m 3. Then
density of the liquid is obtained by multiplying its specific gravity by the density of water,
๏ฒ ๏ฝ SG ๏ด ๏ฒ H 2O ๏ฝ (0.85)(1000 kg/m 3 ) ๏ฝ 850 kg/m 3
Analysis (a) Knowing the absolute pressure, the atmospheric pressure can be
determined from
Patm
Patm ๏ฝ P ๏ญ ๏ฒgh
๏ฆ 1 kPa ๏ถ
๏ท
๏ฝ (185 kPa) ๏ญ (1000 kg/m 3 )(9.81 m/s 2 )(9 m)๏ง
๏ง 1000 N/m 2 ๏ท
๏จ
๏ธ
๏ฝ 96.7 kPa
h
P
(b) The absolute pressure at a depth of 5 m in the other liquid is
P ๏ฝ Patm ๏ซ ๏ฒgh
๏ฆ 1 kPa ๏ถ
๏ท
๏ฝ (96.7 kPa) ๏ซ (850 kg/m 3 )(9.81 m/s 2 )(9 m)๏ง
๏ง 1000 N/m 2 ๏ท
๏จ
๏ธ
๏ฝ 171.8 kPa
Discussion Note that at a given depth, the pressure in the lighter fluid is lower, as expected.
2-38E A submarine is cruising at a specified depth from the water surface. The pressure exerted on the surface of the
submarine by water is to be determined.
Assumptions The variation of the density of water with depth is negligible.
Patm
Properties The specific gravity of seawater is given to be SG = 1.03. The density of
water at 32๏ฐF is 62.4 lbm/ft3 (Table A-3E).
Sea
Analysis The density of the seawater is obtained by multiplying its specific gravity by
h
the density of water,
๏ฒ ๏ฝ SG ๏ด ๏ฒ H 2O ๏ฝ (1.03)(62.4 lbm/ft 3 ) ๏ฝ 64.27 lbm/ft 3
P
The pressure exerted on the surface of the submarine cruising 300 ft below the free
surface of the sea is the absolute pressure at that location:
P ๏ฝ Patm ๏ซ ๏ฒgh
๏ฆ
๏ถ๏ฆ 1 ft 2 ๏ถ
1 lbf
๏ท๏ง
๏ท
๏ฝ (14.7 psia) ๏ซ (64.27 lbm/ft 3 )(32.2 ft/s 2 )(175 ft)๏ง
๏ง 32.2 lbm ๏ ft/s 2 ๏ท๏ง 144 in 2 ๏ท
๏จ
๏ธ๏จ
๏ธ
๏ฝ 92.8 psia
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-11
2-39 The mass of a woman is given. The minimum imprint area per shoe needed to enable her to walk on the snow without
sinking is to be determined.
Assumptions 1 The weight of the person is distributed uniformly on the imprint area of the shoes. 2 One foot carries the
entire weight of a person during walking, and the shoe is sized for walking conditions (rather than standing). 3 The weight
of the shoes is negligible.
Analysis The mass of the woman is given to be 70 kg. For a pressure of 0.5
kPa on the snow, the imprint area of one shoe must be
A๏ฝ
W mg
๏ฝ
P
P
๏ถ๏ฆ 1 kPa ๏ถ
(70 kg)(9.81 m/s 2 ) ๏ฆ๏ง
1N
๏ท
๏ฝ 1.37 m 2
๏ง 1 kg ๏ m/s 2 ๏ท๏ง๏จ 1000 N/m 2 ๏ท๏ธ
0.5 kPa
๏จ
๏ธ
Discussion This is a very large area for a shoe, and such shoes would be impractical
to use. Therefore, some sinking of the snow should be allowed to have shoes of
reasonable size.
๏ฝ
2-40E The vacuum pressure given in kPa unit is to be converted to various units.
Analysis Using the definition of vacuum pressure,
Pgage ๏ฝ not applicable for pressures below atmospheric pressure
Pabs ๏ฝ Patm ๏ญ Pvac ๏ฝ 98 ๏ญ 80 ๏ฝ 18 kPa
Then using the conversion factors,
๏ฆ 1 kN/m 2 ๏ถ
๏ท ๏ฝ 18 kN/m 2
Pabs ๏ฝ (18 kPa)๏ง
๏ง 1 kPa ๏ท
๏จ
๏ธ
๏ฆ 1 lbf/in 2 ๏ถ
๏ท ๏ฝ 2.61 lbf/in 2
Pabs ๏ฝ (18 kPa)๏ง
๏ง 6.895 kPa ๏ท
๏จ
๏ธ
๏ฆ 1 psi ๏ถ
Pabs ๏ฝ (18 kPa)๏ง
๏ท ๏ฝ 2.61 psi
๏จ 6.895 kPa ๏ธ
๏ฆ 1 mm Hg ๏ถ
Pabs ๏ฝ (18 kPa)๏ง
๏ท ๏ฝ 135 mm Hg
๏จ 0.1333 kPa ๏ธ
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-12
2-41 A mountain hiker records the barometric reading before and after a hiking trip. The vertical distance climbed is to be
determined.
Assumptions The variation of air density and the gravitational
650 mbar
acceleration with altitude is negligible.
Properties The density of air is given to be ๏ฒ = 1.20 kg/m3.
Analysis Taking an air column between the top and the bottom of the
mountain and writing a force balance per unit base area, we obtain
h=?
Wair / A ๏ฝ Pbottom ๏ญ Ptop
( ๏ฒgh) air ๏ฝ Pbottom ๏ญ Ptop
750 mbar
๏ฆ
๏ถ๏ฆ
๏ถ
1N
1 bar
๏ท๏ง
๏ท ๏ฝ (0.750 ๏ญ 0.650) bar
(1.20 kg/m 3 )(9.81 m/s 2 )(h)๏ง
๏ง 1 kg ๏ m/s 2 ๏ท๏ง 100,000 N/m 2 ๏ท
๏จ
๏ธ๏จ
๏ธ
It yields
h = 850 m
which is also the distance climbed.
2-42 A barometer is used to measure the height of a building by recording reading at the bottom and at the top of the
building. The height of the building is to be determined.
Assumptions The variation of air density with altitude is negligible.
Properties The density of air is given to be ๏ฒ = 1.18 kg/m3. The density of mercury is
13,600 kg/m3.
Analysis Atmospheric pressures at the top and at the bottom of the building are
675 mmHg
Ptop ๏ฝ ( ฯ g h) top
๏ฆ
๏ถ๏ฆ 1 kPa ๏ถ
1N
๏ท๏ง
๏ท
๏ฝ (13,600 kg/m 3 )(9.81 m/s 2 )(0.675 m)๏ง
๏ง 1 kg ๏ m/s 2 ๏ท๏ง 1000 N/m 2 ๏ท
๏จ
๏ธ
๏จ
๏ธ
๏ฝ 90.06 kPa
h
Pbottom ๏ฝ ( ๏ฒ g h) bottom
๏ฆ
๏ถ๏ฆ 1 kPa ๏ถ
1N
๏ท๏ง
๏ท
๏ฝ (13,600 kg/m 3 )(9.81 m/s 2 )(0.695 m)๏ง
๏ง 1kg ๏ m/s 2 ๏ท๏ง 1000 N/m 2 ๏ท
๏จ
๏ธ
๏จ
๏ธ
๏ฝ 92.72 kPa
695 mmHg
Taking an air column between the top and the bottom of the building and writing a force balance per unit base area, we
obtain
Wair / A ๏ฝ Pbottom ๏ญ Ptop
( ๏ฒgh) air ๏ฝ Pbottom ๏ญ Ptop
๏ฆ
๏ถ๏ฆ 1 kPa ๏ถ
1N
๏ท๏ง
๏ท ๏ฝ (92.72 ๏ญ 90.06) kPa
(1.18 kg/m 3 )(9.81 m/s 2 )(h)๏ง
๏ง 1 kg ๏ m/s 2 ๏ท๏ง 1000 N/m 2 ๏ท
๏จ
๏ธ๏จ
๏ธ
It yields
h = 231 m
which is also the height of the building.
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-13
2-43
Problem 2-42 is reconsidered. The entire software solution is to be printed out, including the numerical results
with proper units.
Analysis The problem is solved using EES, and the solution is given below.
P_bottom=695 [mmHg]
P_top=675 [mmHg]
g=9.81 [m/s^2] “local acceleration of gravity at sea level”
rho=1.18 [kg/m^3]
DELTAP_abs=(P_bottom-P_top)*CONVERT(mmHg, kPa) “[kPa]” “Delta P reading from the barometers,
converted from mmHg to kPa.”
DELTAP_h =rho*g*h*Convert(Pa, kPa) “Delta P due to the air fluid column height, h, between the top and
bottom of the building.”
DELTAP_abs=DELTAP_h
SOLUTION
DELTAP_abs=2.666 [kPa]
DELTAP_h=2.666 [kPa]
g=9.81 [m/s^2]
h=230.3 [m]
P_bottom=695 [mmHg]
P_top=675 [mmHg]
rho=1.18 [kg/m^3]
2-44 The hydraulic lift in a car repair shop is to lift cars. The fluid gage pressure that must be maintained in the reservoir is
to be determined.
Assumptions The weight of the piston of the lift is negligible.
W = mg
Analysis Pressure is force per unit area, and thus the gage pressure required
is simply the ratio of the weight of the car to the area of the lift,
Patm
W
mg
Pgage ๏ฝ
๏ฝ
A ๏ฐD 2 / 4
๏ถ
(2000 kg)(9.81 m/s2 ) ๏ฆ
1 kN
๏ง
๏ท ๏ฝ 278 kN/m 2 ๏ฝ 278 kPa
2
2๏ท
๏ง
๏ฐ (0.30 m) / 4 ๏จ 1000 kg ๏ m/s ๏ธ
P
Discussion Note that the pressure level in the reservoir can be reduced by using a piston with a larger area.
๏ฝ
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-14
2-45 A gas contained in a vertical piston-cylinder device is pressurized by a spring and by the weight of the piston. The
pressure of the gas is to be determined.
Analysis Drawing the free body diagram of the piston and balancing the
Fspring
vertical forces yield
PA ๏ฝ Patm A ๏ซ W ๏ซ Fspring
Patm
Thus,
P ๏ฝ Patm ๏ซ
mg ๏ซ Fspring
A
(3.2 kg)(9.81 m/s 2 ) ๏ซ 150 N ๏ฆ๏ง 1 kPa ๏ถ๏ท
๏ฝ (95 kPa) ๏ซ
๏ง 1000 N/m 2 ๏ท
35 ๏ด 10 ๏ญ 4 m 2
๏จ
๏ธ
๏ฝ 147 kPa
P
W = mg
2-46
Problem 2-45 is reconsidered. The effect of the spring force in the range of 0 to 500 N on the pressure inside the
cylinder is to be investigated. The pressure against the spring force is to be plotted, and results are to be discussed.
Analysis The problem is solved using EES, and the solution is given below.
g=9.81 [m/s^2]
P_atm= 95 [kPa]
m_piston=3.2 [kg]
{F_spring=150 [N]}
A=35*CONVERT(cm^2, m^2)
W_piston=m_piston*g
F_atm=P_atm*A*CONVERT(kPa, N/m^2)
“From the free body diagram of the piston, the balancing vertical forces yield:”
F_gas= F_atm+F_spring+W_piston
P_gas=F_gas/A*CONVERT(N/m^2, kPa)
Pgas
[kPa]
104
118.3
132.5
146.8
161.1
175.4
189.7
204
218.3
232.5
246.8
260
240
220
Pgas [kPa]
Fspring
[N]
0
50
100
150
200
250
300
350
400
450
500
200
180
160
140
120
100
0
100
200
300
400
500
Fspring [N]
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-15
2-47 Both a gage and a manometer are attached to a gas to measure its pressure. For a specified reading of gage
pressure, the difference between the fluid levels of the two arms of the manometer is to be determined for mercury and
water.
Properties The densities of water and mercury are given to be
๏ฒwater = 1000 kg/m3 and be ๏ฒHg = 13,600 kg/m3.
Analysis The gage pressure is related to the vertical distance h between the
two fluid levels by
Pgage ๏ฝ ๏ฒ g h ๏พ
๏พ๏ฎ h ๏ฝ
Pgage
๏ฒg
(a) For mercury,
h๏ฝ
๏ฝ
Pgage
๏ฒ Hg g
๏ฆ 1 kN/m 2 ๏ถ๏ฆ 1000 kg/m ๏ s 2 ๏ถ
๏ท ๏ฝ 0.60 m
๏ง
๏ท๏ง
๏ท
1 kN
(13,600 kg/m 3 )(9.81 m/s 2 ) ๏ง๏จ 1 kPa ๏ท๏ธ๏ง๏จ
๏ธ
80 kPa
(b) For water,
h๏ฝ
Pgage
๏ฒ H 2O g
๏ฝ
๏ฆ 1 kN/m 2 ๏ถ๏ฆ 1000 kg/m ๏ s 2 ๏ถ
๏ท ๏ฝ 8.16 m
๏ง
๏ท๏ง
๏ท
1 kN
(1000 kg/m 3 )(9.81 m/s 2 ) ๏ง๏จ 1 kPa ๏ท๏ธ๏ง๏จ
๏ธ
80 kPa
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-16
2-48
Problem 2-47 is reconsidered. The effect of the manometer fluid density in the range of 800 to 13,000 kg/m 3 on
the differential fluid height of the manometer is to be investigated. Differential fluid height against the density is to be
plotted, and the results are to be discussed.
Analysis The problem is solved using EES, and the solution is given below.
“Let’s modify this problem to also calculate the absolute pressure in the tank by supplying the atmospheric
pressure.
Use the relationship between the pressure gage reading and the manometer fluid column height. ”
Function fluid_density(Fluid$)
“This function is needed since if-then-else logic can only be used in functions or procedures.
The underscore displays whatever follows as subscripts in the Formatted Equations Window.”
If fluid$=’Mercury’ then fluid_density=13600 else fluid_density=1000
end
{Input from the diagram window. If the diagram window is hidden, then all of the input must come from the
equations window. Also note that brackets can also denote comments – but these comments do not appear in
the formatted equations window.}
{Fluid$=’Mercury’
P_atm = 101.325 [kPa]
DELTAP=80 [kPa] “Note how DELTAP is displayed on the Formatted Equations Window.”}
g=9.807 [m/s^2] “local acceleration of gravity at sea level”
rho=Fluid_density(Fluid$) “Get the fluid density, either Hg or H2O, from the function”
“To plot fluid height against density place {} around the above equation. Then set up the parametric table and
solve.”
DELTAP = RHO*g*h/1000
“Instead of dividiing by 1000 Pa/kPa we could have multiplied by the EES function, CONVERT(Pa,kPa)”
h_mm=h*convert(m, mm) “The fluid height in mm is found using the built-in CONVERT function.”
P_abs= P_atm + DELTAP
“To make the graph, hide the diagram window and remove the {}brackets from Fluid$ and from P_atm. Select
New Parametric Table from the Tables menu. Choose P_abs, DELTAP and h to be in the table. Choose Alter
Values from the Tables menu. Set values of h to range from 0 to 1 in steps of 0.2. Choose Solve Table (or
press F3) from the Calculate menu. Choose New Plot Window from the Plot menu. Choose to plot P_abs vs h
and then choose Overlay Plot from the Plot menu and plot DELTAP on the same scale.”
Manometer Fluid Height vs Manometer Fluid Density
hmm
[mm]
10197
3784
2323
1676
1311
1076
913.1
792.8
700.5
627.5
11000
8800
hmm [mm]
๏ฒ
[kg/m3]
800
2156
3511
4867
6222
7578
8933
10289
11644
13000
6600
4400
2200
0
0
2000
4000
6000
8000
10000 12000 14000
๏ฒ๏ ๏ [kg/m^3]
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-17
2-49 The air pressure in a tank is measured by an oil manometer. For a given oil-level difference between the two columns,
the absolute pressure in the tank is to be determined.
Properties The density of oil is given to be ๏ฒ = 850 kg/m3.
Analysis The absolute pressure in the tank is determined from
P ๏ฝ Patm ๏ซ ๏ฒgh
๏ฆ 1kPa ๏ถ
๏ท
๏ฝ (98 kPa) ๏ซ (850 kg/m 3 )(9.81m/s 2 )(0.80 m)๏ง
๏ง 1000N/m 2 ๏ท
๏จ
๏ธ
๏ฝ 104.7 kPa
0.80 m
AIR
Patm = 98 kPa
2-50 The air pressure in a duct is measured by a mercury manometer. For a given
mercury-level difference between the two columns, the absolute pressure in the
duct is to be determined.
Properties The density of mercury is given to be ๏ฒ = 13,600 kg/m3.
Analysis (a) The pressure in the duct is above atmospheric pressure since the
fluid column on the duct side is at a lower level.
(b) The absolute pressure in the duct is determined from
P ๏ฝ Patm ๏ซ ๏ฒgh
AIR
15 mm
P
๏ฆ 1N
๏ถ๏ฆ 1 kPa ๏ถ
๏ท๏ง
๏ท
๏ฝ (100 kPa) ๏ซ (13,600 kg/m 3 )(9.81 m/s 2 )(0.015 m)๏ง
๏ง 1 kg ๏ m/s 2 ๏ท๏ง 1000 N/m 2 ๏ท
๏จ
๏ธ๏จ
๏ธ
๏ฝ 102 kPa
2-51 The air pressure in a duct is measured by a mercury manometer. For a given
mercury-level difference between the two columns, the absolute pressure in the duct is
to be determined.
Properties The density of mercury is given to be ๏ฒ = 13,600 kg/m3.
Analysis (a) The pressure in the duct is above atmospheric pressure since the fluid
column on the duct side is at a lower level.
(b) The absolute pressure in the duct is determined from
P ๏ฝ Patm ๏ซ ๏ฒgh
AIR
45 mm
P
๏ฆ 1N
๏ถ๏ฆ 1 kPa ๏ถ
๏ท๏ง
๏ท
๏ฝ (100 kPa) ๏ซ (13,600 kg/m 3 )(9.81 m/s 2 )(0.045 m)๏ง
๏ง 1 kg ๏ m/s 2 ๏ท๏ง 1000 N/m 2 ๏ท
๏จ
๏ธ๏จ
๏ธ
๏ฝ 106 kPa
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-18
2-52E The pressure in a natural gas pipeline is measured by a double U-tube manometer with one of the arms open to the
atmosphere. The absolute pressure in the pipeline is to be determined.
Assumptions 1 All the liquids are incompressible. 2 The
effect of air column on pressure is negligible. 3 The
Air
pressure throughout the natural gas (including the tube) is
uniform since its density is low.
10in
Properties We take the density of water to be ๏ฒw = 62.4
Water
lbm/ft3. The specific gravity of mercury is given to be 13.6,
and thus its density is ๏ฒHg = 13.6๏ด62.4 = 848.6 lbm/ft3.
hw
Analysis Starting with the pressure at point 1 in the natural
gas pipeline, and moving along the tube by adding (as we
hHg
go down) or subtracting (as we go up) the ๏ฒgh terms until
Natural
we reach the free surface of oil where the oil tube is
gas
exposed to the atmosphere, and setting the result equal to
Patm gives
P1 ๏ญ ๏ฒ Hg ghHg ๏ญ ๏ฒ water ghwater ๏ฝ Patm
Solving for P1,
P1 ๏ฝ Patm ๏ซ ๏ฒ Hg ghHg ๏ซ ๏ฒ water gh1
Mercury
Substituting,
๏ฆ
๏ถ๏ฆ 1 ft 2 ๏ถ
1 lbf
๏ท๏ง
๏ท
P ๏ฝ 14.2 psia ๏ซ (32.2 ft/s 2 )[(848.6 lbm/ft 3 )(6/12 ft) ๏ซ (62.4 lbm/ft 3 )(27/12ft)]๏ง
๏ง 32.2 lbm ๏ ft/s 2 ๏ท๏ง 144 in 2 ๏ท
๏จ
๏ธ
๏จ
๏ธ
๏ฝ 18.1psia
Discussion Note that jumping horizontally from one tube to the next and realizing that pressure remains the same in the
same fluid simplifies the analysis greatly. Also, it can be shown that the 15-in high air column with a density of 0.075
lbm/ft3 corresponds to a pressure difference of 0.00065 psi. Therefore, its effect on the pressure difference between the two
pipes is negligible.
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-19
2-53E The pressure in a natural gas pipeline is measured by a double U-tube manometer with one of the arms open to the
atmosphere. The absolute pressure in the pipeline is to be determined.
Assumptions 1 All the liquids are incompressible. 2 The
pressure throughout the natural gas (including the tube) is
uniform since its density is low.
Oil
Properties We take the density of water to be ๏ฒ w = 62.4
lbm/ft3. The specific gravity of mercury is given to be 13.6,
Water
and thus its density is ๏ฒHg = 13.6๏ด62.4 = 848.6 lbm/ft3. The
specific gravity of oil is given to be 0.69, and thus its
density is ๏ฒoil = 0.69๏ด62.4 = 43.1 lbm/ft3.
hw
Analysis Starting with the pressure at point 1 in the natural
hHg
gas pipeline, and moving along the tube by adding (as we
Natural
go down) or subtracting (as we go up) the ๏ฒgh terms until
hoil
gas
we reach the free surface of oil where the oil tube is
exposed to the atmosphere, and setting the result equal to
Patm gives
P1 ๏ญ ๏ฒ Hg ghHg ๏ซ ๏ฒ oil ghoil ๏ญ ๏ฒ water ghwater ๏ฝ Patm
Solving for P1,
P1 ๏ฝ Patm ๏ซ ๏ฒ Hg ghHg ๏ซ ๏ฒ water gh1 ๏ญ ๏ฒ oil ghoil
Mercury
Substituting,
P1 ๏ฝ 14.2 psia ๏ซ (32.2 ft/s 2 )[(848.6 lbm/ft 3 )(6/12 ft) ๏ซ (62.4 lbm/ft 3 )(27/12ft)
๏ฆ
๏ถ๏ฆ 1 ft 2 ๏ถ
1 lbf
๏ท๏ง
๏ท
๏ญ (43.1 lbm/ft 3 )(15/12 ft)]๏ง
๏ง 32.2 lbm ๏ ft/s 2 ๏ท๏ง 144 in 2 ๏ท
๏จ
๏ธ
๏จ
๏ธ
๏ฝ 17.7 psia
Discussion Note that jumping horizontally from one tube to the next and realizing that pressure remains the same in the
same fluid simplifies the analysis greatly.
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-20
2-54E The systolic and diastolic pressures of a healthy person are given in mmHg. These pressures are to be expressed in
kPa, psi, and meter water column.
Assumptions Both mercury and water are incompressible substances.
Properties We take the densities of water and mercury to be 1000 kg/m3 and 13,600 kg/m3, respectively.
Analysis Using the relation P ๏ฝ ๏ฒgh for gage pressure, the high and low pressures are expressed as
๏ฆ 1N
๏ถ๏ฆ 1 kPa ๏ถ
๏ท๏ง
๏ท ๏ฝ 16.0 kPa
Phigh ๏ฝ ๏ฒghhigh ๏ฝ (13,600 kg/m 3 )(9.81 m/s 2 )(0.12 m)๏ง๏ง
2 ๏ท๏ง
2๏ท
๏จ 1 kg ๏ m/s ๏ธ๏จ 1000 N/m ๏ธ
๏ฆ 1N
๏ถ๏ฆ 1 kPa ๏ถ
๏ท๏ง
๏ท ๏ฝ 10.7 kPa
Plow ๏ฝ ๏ฒghlow ๏ฝ (13,600 kg/m 3 )(9.81 m/s 2 )(0.08 m)๏ง๏ง
2 ๏ท๏ง
2๏ท
๏จ 1 kg ๏ m/s ๏ธ๏จ 1000 N/m ๏ธ
Noting that 1 psi = 6.895 kPa,
๏ฆ 1 psi ๏ถ
๏ท๏ท ๏ฝ 2.32 psi
Phigh ๏ฝ (16.0 Pa)๏ง๏ง
๏จ 6.895kPa ๏ธ
and
๏ฆ 1 psi ๏ถ
๏ท๏ท ๏ฝ 1.55 psi
Plow ๏ฝ (10.7 Pa)๏ง๏ง
๏จ 6.895kPa ๏ธ
For a given pressure, the relation P ๏ฝ ๏ฒgh can be expressed for mercury and water
as P ๏ฝ ๏ฒ water ghwater and P ๏ฝ ๏ฒ mercury ghmercury . Setting these two relations equal to
each other and solving for water height gives
P ๏ฝ ๏ฒ water ghwater ๏ฝ ๏ฒ mercury ghmercury ๏ฎ hwater ๏ฝ
๏ฒ mercury
๏ฒ water
hmercury
h
Therefore,
h water, high ๏ฝ
h water, low ๏ฝ
๏ฒ mercury
๏ฒ water
๏ฒ mercury
๏ฒ water
hmercury, high ๏ฝ
hmercury, low ๏ฝ
13,600 kg/m 3
1000 kg/m 3
13,600 kg/m 3
1000 kg/m 3
(0.12 m) ๏ฝ 1.63 m
(0.08 m) ๏ฝ 1.09 m
Discussion Note that measuring blood pressure with a โwaterโ monometer would involve differential fluid heights higher
than the person, and thus it is impractical. This problem shows why mercury is a suitable fluid for blood pressure
measurement devices.
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-21
2-55 A vertical tube open to the atmosphere is connected to the vein in the arm of a person. The height that the blood will
rise in the tube is to be determined.
Assumptions 1 The density of blood is constant. 2 The gage pressure of blood is 120 mmHg.
Properties The density of blood is given to be ๏ฒ = 1050 kg/m3.
Analysis For a given gage pressure, the relation P ๏ฝ ๏ฒgh can be expressed
for mercury and blood as P ๏ฝ ๏ฒ blood ghblood and P ๏ฝ ๏ฒ mercury ghmercury .
Blood
h
Setting these two relations equal to each other we get
P ๏ฝ ๏ฒ blood ghblood ๏ฝ ๏ฒ mercury ghmercury
Solving for blood height and substituting gives
hblood ๏ฝ
๏ฒ mercury
๏ฒ blood
hmercury ๏ฝ
13,600 kg/m 3
1050 kg/m 3
(0.12 m) ๏ฝ 1.55 m
Discussion Note that the blood can rise about one and a half meters in a tube connected to the vein. This explains why IV
tubes must be placed high to force a fluid into the vein of a patient.
2-56 A diver is moving at a specified depth from the water surface. The pressure exerted on the surface of the diver by
water is to be determined.
Assumptions The variation of the density of water with depth is negligible.
Properties The specific gravity of seawater is given to be SG = 1.03. We take the density of water to be 1000 kg/m 3.
Analysis The density of the seawater is obtained by multiplying
Patm
its specific gravity by the density of water which is taken to be
1000 kg/m3:
Sea
๏ฒ ๏ฝ SG ๏ด ๏ฒ H 2O ๏ฝ (1.03)(1000 kg/m 3 ) ๏ฝ 1030 kg/m 3
h
The pressure exerted on a diver at 45 m below the free surface
of the sea is the absolute pressure at that location:
P
P ๏ฝ Patm ๏ซ ๏ฒgh
๏ฆ 1 kPa ๏ถ
๏ท
๏ฝ (101 kPa) ๏ซ (1030 kg/m 3 )(9.807 m/s 2 )(45 m)๏ง
๏ง 1000 N/m 2 ๏ท
๏จ
๏ธ
๏ฝ 556 kPa
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-22
2-57 Water is poured into the U-tube from one arm and oil from the other arm. The water column height in one arm and the
ratio of the heights of the two fluids in the other arm are given. The height of each fluid in that arm is to be determined.
Assumptions Both water and oil are incompressible substances.
Properties The density of oil is given to be ๏ฒ = 790 kg/m3. We take
the density of water to be ๏ฒ =1000 kg/m3.
Analysis The height of water column in the left arm of the monometer
is given to be hw1 = 0.70 m. We let the height of water and oil in the
right arm to be hw2 and ha, respectively. Then, ha = 4hw2. Noting that
both arms are open to the atmosphere, the pressure at the bottom of
the U-tube can be expressed as
Pbottom ๏ฝ Patm ๏ซ ๏ฒ w ghw1
Water
oil
ha
hw1
hw2
Pbottom ๏ฝ Patm ๏ซ ๏ฒ w ghw2 ๏ซ ๏ฒ a gha
and
Setting them equal to each other and simplifying,
๏ฒ w ghw1 ๏ฝ ๏ฒ w ghw2 ๏ซ ๏ฒ a gha
๏ฎ
๏ฒ w h w1 ๏ฝ ๏ฒ w hw2 ๏ซ ๏ฒ a ha
๏ฎ
h w1 ๏ฝ h w2 ๏ซ ( ๏ฒ a / ๏ฒ w )ha
Noting that ha = 4hw2, the water and oil column heights in the second arm are determined to be
0.7 m ๏ฝ h w2 ๏ซ (790/1000)4 h w2 ๏ฎ
h w2 ๏ฝ 0.168 m
0.7 m ๏ฝ 0.168 m ๏ซ (790/1000)ha ๏ฎ
ha ๏ฝ 0.673 m
Discussion Note that the fluid height in the arm that contains oil is higher. This is expected since oil is lighter than water.
2-58 A double-fluid manometer attached to an air pipe is considered. The specific gravity of one fluid is known, and the
specific gravity of the other fluid is to be determined.
Assumptions 1 Densities of liquids are constant. 2 The air
pressure in the tank is uniform (i.e., its variation with
Air
elevation is negligible due to its low density), and thus the
P = 76 kPa
pressure at the air-water interface is the same as the
indicated gage pressure.
40 cm
Properties The specific gravity of one fluid is given to be
13.55. We take the standard density of water to be 1000
Fluid 2
kg/m3.
SG2
22 cm
Analysis Starting with the pressure of air in the tank, and
Fluid 1
moving along the tube by adding (as we go down) or
SG1
subtracting (as we go up) the ๏ฒgh terms until we reach the
free surface where the oil tube is exposed to the
atmosphere, and setting the result equal to Patm give
Pair ๏ซ ๏ฒ 1 gh1 ๏ญ ๏ฒ 2 gh2 ๏ฝ Patm
๏ฎ Pair ๏ญ Patm ๏ฝ SG2 ๏ฒ w gh2 ๏ญ SG1 ๏ฒ w gh1
Rearranging and solving for SG2,
SG 2 ๏ฝ SG 1
๏ถ๏ฆ 1000 kg ๏ m/s 2 ๏ถ
h1 Pair ๏ญ Patm
0.22 m ๏ฆ๏ง
76 ๏ญ 100 kPa
๏ท๏ง
๏ท ๏ฝ 1.34
๏ซ
๏ฝ 13.55
๏ซ
h2
๏ฒ w gh2
0.40 m ๏ง๏จ (1000 kg/m 3 )(9.81 m/s 2 )(0.40 m) ๏ท๏ธ๏ง๏จ 1 kPa. ๏ m 2 ๏ท๏ธ
Discussion Note that the right fluid column is higher than the left, and this would imply above atmospheric pressure in the
pipe for a single-fluid manometer.
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-23
2-59 Fresh and seawater flowing in parallel horizontal pipelines are connected to each other by a double U-tube manometer.
The pressure difference between the two pipelines is to be determined.
Assumptions 1 All the liquids are incompressible. 2 The effect
of air column on pressure is negligible.
Air
Properties The densities of seawater and mercury are given to
be ๏ฒsea = 1035 kg/m3 and ๏ฒHg = 13,600 kg/m3. We take the
density of water to be ๏ฒ w =1000 kg/m3.
hsea
Analysis Starting with the pressure in the fresh water pipe
(point 1) and moving along the tube by adding (as we go down)
or subtracting (as we go up) the ๏ฒgh terms until we reach the
Sea
Fresh
sea water pipe (point 2), and setting the result equal to P2 gives
Water
h
air
Water
P ๏ซ ๏ฒ gh ๏ญ ๏ฒ gh ๏ญ ๏ฒ gh ๏ซ ๏ฒ gh ๏ฝ P
1
w
w
Hg
Hg
air
air
sea
sea
2
Rearranging and neglecting the effect of air column on pressure,
P1 ๏ญ P2 ๏ฝ ๏ญ ๏ฒ w ghw ๏ซ ๏ฒ Hg ghHg ๏ญ ๏ฒ sea ghsea ๏ฝ g ( ๏ฒ Hg hHg ๏ญ ๏ฒ w hw ๏ญ ๏ฒ sea hsea )
hw
hHg
Mercury
Substituting,
P1 ๏ญ P2 ๏ฝ (9.81 m/s 2 )[(13600 kg/m 3 )(0.1 m)
๏ฆ
๏ถ
1 kN
๏ท
๏ญ (1000 kg/m 3 )(0.6 m) ๏ญ (1035 kg/m 3 )(0.4 m)]๏ง
๏ง 1000 kg ๏ m/s 2 ๏ท
๏จ
๏ธ
๏ฝ 3.39 kN/m 2 ๏ฝ 3.39 kPa
Therefore, the pressure in the fresh water pipe is 3.39 kPa higher than the pressure in the sea water pipe.
Discussion A 0.70-m high air column with a density of 1.2 kg/m3 corresponds to a pressure difference of 0.008 kPa.
Therefore, its effect on the pressure difference between the two pipes is negligible.
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-24
2-60 Fresh and seawater flowing in parallel horizontal pipelines are connected to each other by a double U-tube manometer.
The pressure difference between the two pipelines is to be determined.
Assumptions All the liquids are incompressible.
Properties The densities of seawater and mercury are given to
Oil
be ๏ฒsea = 1035 kg/m3 and ๏ฒHg = 13,600 kg/m3. We take the
density of water to be ๏ฒ w =1000 kg/m3. The specific gravity of
oil is given to be 0.72, and thus its density is 720 kg/m3.
hsea
Analysis Starting with the pressure in the fresh water pipe
(point 1) and moving along the tube by adding (as we go down)
or subtracting (as we go up) the ๏ฒgh terms until we reach the
Sea
Fresh
sea water pipe (point 2), and setting the result equal to P2 gives
Water
h
oil
Water
P1 ๏ซ ๏ฒ w ghw ๏ญ ๏ฒ Hg ghHg ๏ญ ๏ฒ oil ghoil ๏ซ ๏ฒ sea ghsea ๏ฝ P2
hw
Rearranging,
hHg
P1 ๏ญ P2 ๏ฝ ๏ญ ๏ฒ w ghw ๏ซ ๏ฒ Hg ghHg ๏ซ ๏ฒ oil ghoil ๏ญ ๏ฒ sea ghsea
Mercury
๏ฝ g(๏ฒ h ๏ซ ๏ฒ h ๏ญ ๏ฒ h ๏ญ ๏ฒ h )
Hg Hg
oil oil
w w
sea sea
Substituting,
P1 ๏ญ P2 ๏ฝ (9.81 m/s 2 )[(13600 kg/m 3 )(0.1 m) ๏ซ (720 kg/m 3 )(0.7 m) ๏ญ (1000 kg/m 3 )(0.6 m)
๏ฆ
๏ถ
1 kN
๏ท
๏ญ (1035 kg/m 3 )(0.4 m)]๏ง
๏ง 1000 kg ๏ m/s 2 ๏ท
๏จ
๏ธ
๏ฝ 8.34 kN/m 2 ๏ฝ 8.34 kPa
Therefore, the pressure in the fresh water pipe is 8.34 kPa higher than the pressure in the sea water pipe.
2-61 The pressure indicated by a manometer is to be determined.
Properties The specific weights of fluid A and fluid B are
given to be 10 kN/m3 and 8 kN/m3, respectively.
Analysis The absolute pressure P1 is determined from
P1 ๏ฝ Patm ๏ซ ( ๏ฒgh) A ๏ซ ( ๏ฒgh) B
๏ฝ Patm ๏ซ ๏ง A h A ๏ซ ๏ง B h B
๏ฆ 0.1333 kPa ๏ถ
๏ท๏ท
๏ฝ (758 mm Hg) ๏ง๏ง
๏จ 1 mm Hg ๏ธ
= hB
hA =
๏ซ (10 kN/m 3 )(0.05 m) ๏ซ (8 kN/m 3 )(0.15 m)
๏ฝ 102.7 kPa
Note that 1 kPa = 1 kN/m2.
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-25
2-62 The pressure indicated by a manometer is to be determined.
Properties The specific weights of fluid A and fluid B
are given to be 100 kN/m3 and 8 kN/m3, respectively.
Analysis The absolute pressure P1 is determined from
P1 ๏ฝ Patm ๏ซ ( ๏ฒgh) A ๏ซ ( ๏ฒgh) B
๏ฝ Patm ๏ซ ๏ง A h A ๏ซ ๏ง B h B
= hB
๏ฝ 90 kPa ๏ซ (100 kN/m 3 )(0.05 m) ๏ซ (8 kN/m 3 )(0.15 m)
๏ฝ 96.2 kPa
Note that 1 kPa = 1 kN/m2.
hA =
100 kN/m3
2-63 The pressure indicated by a manometer is to be determined.
Properties The specific weights of fluid A and fluid B are
given to be 10 kN/m3 and 20 kN/m3, respectively.
Analysis The absolute pressure P1 is determined from
P1 ๏ฝ Patm ๏ซ ( ๏ฒgh) A ๏ซ ( ๏ฒgh) B
๏ฝ Patm ๏ซ ๏ง A h A ๏ซ ๏ง B hB
= hB
๏ฆ 0.1333 kPa ๏ถ
๏ท๏ท
๏ฝ (720 mm Hg) ๏ง๏ง
๏จ 1 mm Hg ๏ธ
hA =
๏ซ (10 kN/m )(0.05 m) ๏ซ (20 kN/m )(0.15 m)
3
3
20 kN/m3
๏ฝ 99.5 kPa
Note that 1 kPa = 1 kN/m2.
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-26
2-64 The fluid levels in a multi-fluid U-tube manometer change as a result of a pressure drop in the trapped air space. For a
given pressure drop and brine level change, the area ratio is to be determined.
Assumptions 1 All the liquids are incompressible. 2
Pressure in the brine pipe remains constant. 3 The
variation of pressure in the trapped air space is
A
negligible.
Air
Properties The specific gravities are given to be 13.56
B
for mercury and 1.1 for brine. We take the standard
Brine
density of water to be ๏ฒw =1000 kg/m3.
pipe
Area, A1
Analysis It is clear from the problem statement and the
Water
figure that the brine pressure is much higher than the air
pressure, and when the air pressure drops by 0.7 kPa, the
SG=1.1
pressure difference between the brine and the air space
increases also by the same amount.
๏hb = 5 mm
Mercury
Starting with the air pressure (point A) and moving
SG=13.56
along the tube by adding (as we go down) or subtracting
(as we go up) the ๏ฒgh terms until we reach the brine
Area, A2
pipe (point B), and setting the result equal to PB before
and after the pressure change of air give
Before:
PA1 ๏ซ ๏ฒ w ghw ๏ซ ๏ฒ Hg ghHg, 1 ๏ญ ๏ฒ br ghbr,1 ๏ฝ PB
After:
PA2 ๏ซ ๏ฒ w ghw ๏ซ ๏ฒ Hg ghHg, 2 ๏ญ ๏ฒ br ghbr,2 ๏ฝ PB
Subtracting,
PA2 ๏ญ PA1 ๏ซ ๏ฒ Hg g๏hHg ๏ญ ๏ฒ br g๏hbr ๏ฝ 0 ๏ฎ
PA1 ๏ญ PA2
๏ฝ SGHg ๏hHg ๏ญ SGbr ๏hbr ๏ฝ 0
๏ฒwg
(1)
where ๏hHg and ๏h br are the changes in the differential mercury and brine column heights, respectively, due to the drop in
air pressure. Both of these are positive quantities since as the mercury-brine interface drops, the differential fluid heights for
both mercury and brine increase. Noting also that the volume of mercury is constant, we have A1๏hHg, left ๏ฝ A2 ๏hHg, right and
PA2 ๏ญ PA1 ๏ฝ ๏ญ0.7 kPa ๏ฝ ๏ญ700 N/m 2 ๏ฝ ๏ญ700 kg/m ๏ s 2
๏h br ๏ฝ 0.005 m
๏hHg ๏ฝ ๏hHg, right ๏ซ ๏hHg,left ๏ฝ ๏hbr ๏ซ ๏hbr A2 /A1 ๏ฝ ๏hbr (1 ๏ซ A2 /A1 )
Substituting,
700 kg/m ๏ s 2
(1000 kg/m 3 )(9.81 m/s 2 )
๏ฝ [13.56๏ด 0.005(1๏ซ A2 /A1 ) ๏ญ (1.1๏ด 0.005)]m
It gives
A2/A1 = 0.134
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-27
Review Problems
2-65 A hydraulic lift is used to lift a weight. The diameter of the
piston on which the weight to be placed is to be determined.
Assumptions 1 The cylinders of the lift are vertical. 2
There are no leaks. 3 Atmospheric pressure act on both
sides, and thus it can be disregarded.
Analysis Noting that pressure is force per unit area, the
pressure on the smaller piston is determined from
F
m1 g
P1 ๏ฝ 1 ๏ฝ
A1 ๏ฐD12 / 4
๏ฝ
F1
25 kg
Weight
2500 kg
F2
10 cm
D2
๏ถ
(25 kg)(9.81 m/s ) ๏ฆ
1 kN
๏ง
๏ท
2
2๏ท
๏ง
๏ฐ (0.10 m) / 4 ๏จ 1000 kg ๏ m/s ๏ธ
2
๏ฝ 31.23 kN/m 2 ๏ฝ 31.23 kPa
From Pascalโs principle, the pressure on the greater piston is equal to that in the smaller piston. Then, the needed diameter is
determined from
P1 ๏ฝ P2 ๏ฝ
๏ถ
F2
m2 g
(2500 kg)(9.81 m/s 2 ) ๏ฆ๏ง
1 kN
2
๏ท๏พ
๏ฝ
๏พ
๏พ๏ฎ
31
.
23
kN/m
๏ฝ
๏พ๏ฎ D 2 ๏ฝ 1.0 m
2
2
2
๏ง
๏ท
A2 ๏ฐD 2 / 4
1000
kg
๏
m/s
๏ฐD 2 / 4
๏จ
๏ธ
Discussion Note that large weights can be raised by little effort in hydraulic lift by making use of Pascalโs principle.
2-66E The efficiency of a refrigerator increases by 3% per ๏ฐC rise in the minimum temperature. This increase is to be
expressed per ๏ฐF, K, and R rise in the minimum temperature.
Analysis The magnitudes of 1 K and 1๏ฐC are identical, so are the magnitudes of 1 R and 1๏ฐF. Also, a change of 1 K or 1๏ฐC
in temperature corresponds to a change of 1.8 R or 1.8๏ฐF. Therefore, the increase in efficiency is
(a) 3% for each K rise in temperature, and
(b), (c) 3/1.8 = 1.67% for each R or ๏ฐF rise in temperature.
2-67E Hyperthermia of 5๏ฐC is considered fatal. This fatal level temperature change of body temperature is to be expressed
in ๏ฐF, K, and R.
Analysis The magnitudes of 1 K and 1๏ฐC are identical, so are the magnitudes of 1 R and 1๏ฐF. Also, a change of 1 K or 1๏ฐC
in temperature corresponds to a change of 1.8 R or 1.8๏ฐF. Therefore, the fatal level of hypothermia is
(a) 5 K
(b) 5๏ด1.8 = 9๏ฐF
(c) 5๏ด1.8 = 9 R
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-28
2-68E A house is losing heat at a rate of 1800 kJ/h per ๏ฐC temperature difference between the indoor and the outdoor
temperatures. The rate of heat loss is to be expressed per ๏ฐF, K, and R of temperature difference between the indoor and the
outdoor temperatures.
Analysis The magnitudes of 1 K and 1๏ฐC are identical, so are the magnitudes of 1 R and 1๏ฐF. Also, a change of 1 K or 1๏ฐC
in temperature corresponds to a change of 1.8 R or 1.8๏ฐF. Therefore, the rate of heat loss from the house is
(a) 1800 kJ/h per K difference in temperature, and
(b), (c) 1800/1.8 = 1000 kJ/h per R or ๏ฐF rise in temperature.
2-69 The average temperature of the atmosphere is expressed as Tatm = 288.15 โ 6.5z where z is altitude in km. The
temperature outside an airplane cruising at 12,000 m is to be determined.
Analysis Using the relation given, the average temperature of the atmosphere at an altitude of 12,000 m is determined to be
Tatm = 288.15 – 6.5z
= 288.15 – 6.5๏ด12
= 210.15 K = – 63๏ฐC
Discussion This is the โaverageโ temperature. The actual temperature at different times can be different.
2-70 A new โSmithโ absolute temperature scale is proposed, and a value of 1000 S is assigned to the boiling point of water.
The ice point on this scale, and its relation to the Kelvin scale are to be determined.
Analysis All linear absolute temperature scales read zero at absolute zero pressure, and are
S
K
constant multiples of each other. For example, T(R) = 1.8 T(K). That is, multiplying a
temperature value in K by 1.8 will give the same temperature in R.
373.15
1000
The proposed temperature scale is an acceptable absolute temperature scale since it
differs from the other absolute temperature scales by a constant only. The boiling temperature
of water in the Kelvin and the Smith scales are 315.15 K and 1000 K, respectively. Therefore,
these two temperature scales are related to each other by
1000
T (K) ๏ฝ 2.6799T(K )
373.15
The ice point of water on the Smith scale is
T (S ) ๏ฝ
T(S)ice = 2.6799 T(K)ice = 2.6799๏ด273.15 = 732.0 S
0
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-29
2-71E An expression for the equivalent wind chill temperature is given in English units. It is to be converted to SI units.
Analysis The required conversion relations are 1 mph = 1.609 km/h and T(๏ฐF) = 1.8T(๏ฐC) + 32. The first thought that comes
to mind is to replace T(๏ฐF) in the equation by its equivalent 1.8T(๏ฐC) + 32, and V in mph by 1.609 km/h, which is the
โregularโ way of converting units. However, the equation we have is not a regular dimensionally homogeneous equation,
and thus the regular rules do not apply. The V in the equation is a constant whose value is equal to the numerical value of
the velocity in mph. Therefore, if V is given in km/h, we should divide it by 1.609 to convert it to the desired unit of mph.
That is,
Tequiv (๏ฐ F) ๏ฝ 914
. ๏ญ [914
. ๏ญ Tambient (๏ฐ F)][0.475 ๏ญ 0.0203(V / 1609
. ) ๏ซ 0.304 V / 1609
.
]
or
Tequiv (๏ฐ F) ๏ฝ 914
. ๏ญ [914
. ๏ญ Tambient (๏ฐ F)][0.475 ๏ญ 0.0126V ๏ซ 0.240 V ]
where V is in km/h. Now the problem reduces to converting a temperature in ๏ฐF to a temperature in ๏ฐC, using the proper
convection relation:
18
. Tequiv (๏ฐ C) ๏ซ 32 ๏ฝ 914
. ๏ญ [914
. ๏ญ (18
. Tambient (๏ฐ C) ๏ซ 32)][0.475 ๏ญ 0.0126V ๏ซ 0.240 V ]
which simplifies to
Tequiv (๏ฐ C) ๏ฝ 33.0 ๏ญ (33.0 ๏ญ Tambient )(0.475 ๏ญ 0.0126V ๏ซ 0.240 V )
where the ambient air temperature is in ๏ฐC.
2-72E
Problem 2-71E is reconsidered. The equivalent wind-chill temperatures in ยฐF as a function of wind velocity in
the range of 4 mph to 40 mph for the ambient temperatures of 20, 40, and 60ยฐF are to be plotted, and the results are to be
discussed.
Analysis The problem is solved using EES, and the solution is given below.
T_ambient=20
“V=20”
T_equiv=91.4-(91.4-T_ambient)*(0.475 – 0.0203*V + 0.304*sqrt(V))
Tequiv
[F]
59.94
54.59
51.07
48.5
46.54
45.02
43.82
42.88
42.16
41.61
The table is for Tambient=60ยฐF
60
T amb = 60ยฐF
50
40
30
Tequiv [F]
V
[mph]
4
8
12
16
20
24
28
32
36
40
T amb = 40ยฐF
20
10
0
T amb = 20ยฐF
-10
-20
0
5
10
15
20
25
30
35
40
V [mph]
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-30
2-73 A vertical piston-cylinder device contains a gas. Some weights are to be placed on the piston to increase the gas
pressure. The local atmospheric pressure and the mass of the weights that will double the pressure of the gas are to be
determined.
Assumptions Friction between the piston and the cylinder is negligible.
Analysis The gas pressure in the piston-cylinder device initially depends on the local
WEIGTHS
atmospheric pressure and the weight of the piston. Balancing the vertical forces yield
๏ถ
(5 kg)(9.81 m/s 2 ) ๏ฆ๏ง
1 kN
๏ท ๏ฝ 95.66 kN/m 2 ๏ฝ 95.7 kPa
2
2
๏ง
A
๏ฐ (0.12 m )/4 ๏จ 1000 kg ๏ m/s ๏ท๏ธ
The force balance when the weights are placed is used to determine the mass of the weights
(m piston ๏ซ m weights ) g
P ๏ฝ Patm ๏ซ
A
(5 kg ๏ซ m weights )(9.81m/s 2 ) ๏ฆ
๏ถ
1 kN
๏ง
๏ท๏พ
200 kPa ๏ฝ 95.66 kPa ๏ซ
๏พ๏ฎ m weights ๏ฝ 115 kg
๏ง 1000 kg ๏ m/s 2 ๏ท
๏ฐ (0.12 m 2 )/4
๏จ
๏ธ
A large mass is needed to double the pressure.
Patm ๏ฝ P ๏ญ
m piston g
๏ฝ 100 kPa ๏ญ
GAS
2-74 One section of the duct of an air-conditioning system is laid underwater. The upward force the water will exert on the
duct is to be determined.
Assumptions 1 The diameter given is the outer diameter of the duct (or, the thickness of the duct material is negligible). 2
The weight of the duct and the air in is negligible.
Properties The density of air is given to be ๏ฒ = 1.30 kg/m3. We take the
density of water to be 1000 kg/m3.
Analysis Noting that the weight of the duct and the air in it is negligible,
the net upward force acting on the duct is the buoyancy force exerted by
water. The volume of the underground section of the duct is
D =15 cm
L = 35 m
FB
V ๏ฝ AL ๏ฝ (๏ฐD 2 / 4) L ๏ฝ [๏ฐ (0.15 m) 2 /4](35 m) = 0.6185 m 3
Then the buoyancy force becomes
๏ฆ
๏ถ
1 kN
๏ท ๏ฝ 6.07 kN
FB ๏ฝ ๏ฒgV ๏ฝ (1000 kg/m 3 )(9.81 m/s 2 )(0.6185m 3 )๏ง
๏ง 1000 kg ๏ m/s 2 ๏ท
๏จ
๏ธ
Discussion The upward force exerted by water on the duct is 6.07 kN, which is equivalent to the weight of a mass of 619
kg. Therefore, this force must be treated seriously.
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-31
2-75E The average body temperature of a person rises by about 2๏ฐC during strenuous exercise. This increase in temperature
is to be expressed in ๏ฐF, K, and R.
Analysis The magnitudes of 1 K and 1๏ฐC are identical, so are the magnitudes of 1 R and 1๏ฐF. Also, a change of 1 K or 1๏ฐC
in temperature corresponds to a change of 1.8 R or 1.8๏ฐF. Therefore, the rise in the body temperature during strenuous
exercise is
(a) 2 K
(b) 2๏ด1.8 = 3.6๏ฐF
(c) 2๏ด1.8 = 3.6 R
2-76 A helium balloon tied to the ground carries 2 people. The acceleration of the balloon when it is first released is to be
determined.
Assumptions The weight of the cage and the ropes of the balloon is negligible.
Properties The density of air is given to be ๏ฒ = 1.16 kg/m3. The density of helium gas is 1/7th of this.
Analysis The buoyancy force acting on the balloon is
V balloon ๏ฝ 4ฯ r 3 /3 ๏ฝ 4ฯ(6 m) 3 /3 ๏ฝ 904.8 m 3
FB ๏ฝ ๏ฒ air gV balloon
๏ฆ
๏ถ
1N
๏ท ๏ฝ 10,296 N
๏ฝ (1.16 kg/m 3 )(9.81m/s 2 )(904.8 m 3 )๏ง
2
๏ง 1 kg ๏ m/s ๏ท
๏จ
๏ธ
D =12 m
The total mass is
๏ฆ 1.16
๏ถ
m He ๏ฝ ๏ฒ HeV ๏ฝ ๏ง
kg/m 3 ๏ท(904.8 m 3 ) ๏ฝ 149.9 kg
๏จ 7
๏ธ
m total ๏ฝ m He ๏ซ m people ๏ฝ 149.9 ๏ซ 2 ๏ด 85 ๏ฝ 319.9 kg
The total weight is
๏ฆ
๏ถ
1N
๏ท ๏ฝ 3138 N
W ๏ฝ m total g ๏ฝ (319.9 kg)(9.81 m/s 2 )๏ง
๏ง 1 kg ๏ m/s 2 ๏ท
๏จ
๏ธ
Thus the net force acting on the balloon is
Fnet ๏ฝ FB ๏ญ W ๏ฝ 10,296 ๏ญ 3138 ๏ฝ 7157 N
m = 170 kg
Then the acceleration becomes
a๏ฝ
Fnet
7157 N ๏ฆ๏ง 1kg ๏ m/s 2 ๏ถ๏ท
๏ฝ
๏ฝ 22.4 m/s 2
๏ท
m total 319.9 kg ๏ง๏จ
1N
๏ธ
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-32
2-77
Problem 2-76 is reconsidered. The effect of the number of people carried in the balloon on acceleration is to be
investigated. Acceleration is to be plotted against the number of people, and the results are to be discussed.
Analysis The problem is solved using EES, and the solution is given below.
“Given”
D=12 [m]
N_person=2
m_person=85 [kg]
rho_air=1.16 [kg/m^3]
rho_He=rho_air/7
“Analysis”
g=9.81 [m/s^2]
V_ballon=pi*D^3/6
F_B=rho_air*g*V_ballon
m_He=rho_He*V_ballon
m_people=N_person*m_person
m_total=m_He+m_people
W=m_total*g
F_net=F_B-W
a=F_net/m_total
35
30
25
2
1
2
3
4
5
6
7
8
9
10
a
[m/s2]
34
22.36
15.61
11.2
8.096
5.79
4.01
2.595
1.443
0.4865
a [m/s ]
Nperson
20
15
10
5
0
1
2
3
4
5
6
7
8
9
10
N pe rson
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-33
2-78 A balloon is filled with helium gas. The maximum amount of load the balloon can carry is to be determined.
Assumptions The weight of the cage and the ropes of the balloon is negligible.
Properties The density of air is given to be ๏ฒ = 1.16 kg/m3. The density of
helium gas is 1/7th of this.
Analysis The buoyancy force acting on the balloon is
D =12 m
V balloon ๏ฝ 4ฯ r 3 /3 ๏ฝ 4ฯ(6 m) 3 /3 ๏ฝ 904.8 m 3
FB ๏ฝ ๏ฒ air gV balloon
๏ฆ
๏ถ
1N
๏ท ๏ฝ 10,296 N
๏ฝ (1.16 kg/m 3 )(9.81m/s 2 )(904.8 m 3 )๏ง
๏ง 1 kg ๏ m/s 2 ๏ท
๏จ
๏ธ
The mass of helium is
๏ฆ 1.16
๏ถ
mHe ๏ฝ ๏ฒ HeV ๏ฝ ๏ง
kg/m 3 ๏ท(904.8 m 3 ) ๏ฝ 149.9 kg
7
๏จ
๏ธ
In the limiting case, the net force acting on the balloon will be zero. That is,
the buoyancy force and the weight will balance each other:
W ๏ฝ mg ๏ฝ FB
m total ๏ฝ
FB 10,296 N
๏ฝ
๏ฝ 1050 kg
g
9.81 m/s 2
Thus,
mpeople ๏ฝ m total ๏ญ mHe ๏ฝ 1050 ๏ญ 149.9 ๏ฝ 900 kg
2-79 A 6-m high cylindrical container is filled with equal volumes of water and oil. The pressure difference between the top
and the bottom of the container is to be determined.
Properties The density of water is given to be ๏ฒ = 1000 kg/m3. The
specific gravity of oil is given to be 0.85.
Analysis The density of the oil is obtained by multiplying its specific
gravity by the density of water,
Oil
SG = 0.85
๏ฒ ๏ฝ SG ๏ด ๏ฒ H 2O ๏ฝ (0.85)(1000 kg/m 3 ) ๏ฝ 850 kg/m 3
h=6m
The pressure difference between the top and the bottom of the
cylinder is the sum of the pressure differences across the two fluids,
๏Ptotal ๏ฝ ๏Poil ๏ซ ๏Pwater ๏ฝ ( ๏ฒgh) oil ๏ซ ( ๏ฒgh) water
๏
Water
๏
๏ฆ 1 kPa ๏ถ
๏ท
๏ฝ (850 kg/m 3 )(9.81 m/s 2 )(3 m) ๏ซ (1000 kg/m 3 )(9.81 m/s 2 )(3 m) ๏ง
๏ง 1000 N/m 2 ๏ท
๏จ
๏ธ
๏ฝ 54.4 kPa
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-34
2-80 The pressure of a gas contained in a vertical piston-cylinder device is measured to be 180 kPa. The mass of the piston
is to be determined.
Assumptions There is no friction between the piston and the cylinder.
Patm
Analysis Drawing the free body diagram of the piston and balancing the
vertical forces yield
W ๏ฝ PA ๏ญ Patm A
mg ๏ฝ ( P ๏ญ Patm ) A
๏ฆ 1000 kg/m ๏ s 2 ๏ถ
๏ท
(m)(9.81 m/s 2 ) ๏ฝ (180 ๏ญ 100 kPa)(25 ๏ด 10 ๏ญ 4 m 2 )๏ง
๏ง
๏ท
1kPa
๏จ
๏ธ
It yields
P
W = mg
m = 20.4 kg
2-81 The gage pressure in a pressure cooker is maintained constant at 100 kPa by a petcock. The mass of the petcock is to
be determined.
Assumptions There is no blockage of the pressure release valve.
Patm
Analysis Atmospheric pressure is acting on all surfaces of the petcock, which
balances itself out. Therefore, it can be disregarded in calculations if we use the
gage pressure as the cooker pressure. A force balance on the petcock (๏Fy = 0)
yields
P
W ๏ฝ Pgage A
W = mg
Pgage A (100 kPa)(4 ๏ด 10 ๏ญ6 m 2 ) ๏ฆ 1000 kg/m ๏ s 2 ๏ถ
๏ง
๏ท
m๏ฝ
๏ฝ
๏ง
๏ท
g
1 kPa
9.81 m/s 2
๏จ
๏ธ
๏ฝ 0.0408 kg
2-82 A glass tube open to the atmosphere is attached to a water pipe, and the pressure at the bottom of the tube is measured.
It is to be determined how high the water will rise in the tube.
Properties The density of water is given to be ๏ฒ = 1000 kg/m3.
Analysis The pressure at the bottom of the tube can be expressed as
P ๏ฝ Patm ๏ซ ( ๏ฒ g h) tube
Solving for h,
h๏ฝ
P ๏ญ Patm
๏ฒg
๏ฆ 1 kg ๏ m/s 2 ๏ถ๏ฆ 1000 N/m 2 ๏ถ
๏ง
๏ท๏ง
๏ท
๏ท๏ง 1 kPa ๏ท
1N
(1000 kg/m 3 )(9.81 m/s 2 ) ๏ง๏จ
๏ธ๏จ
๏ธ
๏ฝ 1.12 m
๏ฝ
(110 ๏ญ 99) kPa
h
Patm= 99 kPa
Water
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-35
2-83E Equal volumes of water and oil are poured into a U-tube from different arms, and the oil side is pressurized until the
contact surface of the two fluids moves to the bottom and the liquid levels in both arms become the same. The excess
pressure applied on the oil side is to be determined.
Assumptions 1 Both water and oil are incompressible substances. 2 Oil
does not mix with water. 3 The cross-sectional area of the U-tube is
constant.
Properties The density of oil is given to be ๏ฒoil = 49.3 lbm/ft3. We take the
density of water to be ๏ฒw = 62.4 lbm/ft3.
Analysis Noting that the pressure of both the water and the oil is the
same at the contact surface, the pressure at this surface can be expressed
as
Pcontact ๏ฝ Pblow ๏ซ ๏ฒ a gha ๏ฝ Patm ๏ซ ๏ฒ w ghw
Noting that ha = hw and rearranging,
Pgage, blow ๏ฝ Pblow ๏ญ Patm ๏ฝ ( ๏ฒ w ๏ญ ๏ฒ oil ) gh
๏ฆ
๏ถ๏ฆ 1 ft 2 ๏ถ
1 lbf
๏ท๏ง
๏ท
๏ฝ (62.4 – 49.3 lbm/ft 3 )(32.2 ft/s 2 )(30/12 ft)๏ง
๏ง 32.2 lbm ๏ ft/s 2 ๏ท๏ง 144 in 2 ๏ท
๏จ
๏ธ
๏จ
๏ธ
๏ฝ 0.227 psi
Discussion When the person stops blowing, the oil will rise and some water will flow into the right arm. It can be shown
that when the curvature effects of the tube are disregarded, the differential height of water will be 23.7 in to balance 30-in of
oil.
2-84 A barometer is used to measure the altitude of a plane relative to the ground. The barometric readings at the ground
and in the plane are given. The altitude of the plane is to be determined.
Assumptions The variation of air density with altitude is negligible.
Properties The densities of air and mercury are given to be ๏ฒ = 1.20 kg/m3 and ๏ฒ = 13,600 kg/m3.
Analysis Atmospheric pressures at the location of the plane and the ground level are
Pplane ๏ฝ ( ๏ฒ g h) plane
๏ฆ
๏ถ๏ฆ 1 kPa ๏ถ
1N
๏ท๏ง
๏ท
๏ฝ (13,600 kg/m 3 )(9.81 m/s 2 )(0.690 m)๏ง
2
๏ง 1 kg ๏ m/s ๏ท๏ง 1000 N/m 2 ๏ท
๏จ
๏ธ
๏จ
๏ธ
๏ฝ 92.06 kPa
Pground ๏ฝ ( ๏ฒ g h) ground
๏ฆ
๏ถ๏ฆ 1 kPa ๏ถ
1N
๏ท๏ง
๏ท
๏ฝ (13,600 kg/m 3 )(9.81 m/s 2 )(0.753 m)๏ง
๏ง 1 kg ๏ m/s 2 ๏ท๏ง 1000 N/m 2 ๏ท
๏จ
๏ธ
๏จ
๏ธ
๏ฝ 100.46 kPa
Taking an air column between the airplane and the ground and writing a force balance
per unit base area, we obtain
Wair / A ๏ฝ Pground ๏ญ Pplane
h
( ๏ฒ g h) air ๏ฝ Pground ๏ญ Pplane
๏ฆ
๏ถ๏ฆ 1 kPa ๏ถ
1N
๏ท๏ง
๏ท ๏ฝ (100.46 ๏ญ 92.06) kPa
(1.20 kg/m 3 )(9.81 m/s 2 )(h)๏ง
๏ง 1 kg ๏ m/s 2 ๏ท๏ง 1000 N/m 2 ๏ท
๏จ
๏ธ๏จ
๏ธ
It yields
0 Sea
level
h = 714 m
which is also the altitude of the airplane.
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-36
2-85E A water pipe is connected to a double-U manometer whose free arm is open to the atmosphere. The absolute
pressure at the center of the pipe is to be determined.
Assumptions 1 All the liquids are incompressible. 2 The solubility
of the liquids in each other is negligible.
Properties The specific gravities of mercury and oil are given to be
13.6 and 0.80, respectively. We take the density of water to be
๏ฒw = 62.4 lbm/ft3.
Analysis Starting with the pressure at the center of the water pipe,
20 in
and moving along the tube by adding (as we go down) or
30 in
subtracting (as we go up) the ๏ฒgh terms until we reach the free
surface of oil where the oil tube is exposed to the atmosphere, and
setting the result equal to Patm gives
25 in
Pwater pipe ๏ญ ๏ฒ water ghwater ๏ซ ๏ฒ oil ghoil ๏ญ ๏ฒ Hg ghHg ๏ญ ๏ฒ oil ghoil ๏ฝ Patm
Solving for Pwater pipe,
Pwater pipe ๏ฝ Patm ๏ซ ๏ฒ water g (hwater ๏ญ SGoil hoil ๏ซ SGHg hHg ๏ซ SGoil hoil )
Substituting,
Pwater pipe ๏ฝ 14.2psia ๏ซ (62.4lbm/ft 3 )(32.2 ft/s 2 )[(20/12 ft) ๏ญ 0.8(60/12 ft) ๏ซ 13.6(25/12 ft)
๏ฆ
๏ถ๏ฆ 1 ft 2 ๏ถ
1 lbf
๏ท๏ง
๏ท
๏ซ 0.8(30/12 ft)] ๏ด ๏ง
๏ง 32.2 lbm ๏ ft/s 2 ๏ท๏ง 144 in 2 ๏ท
๏จ
๏ธ
๏จ
๏ธ
๏ฝ 26.4 psia
Therefore, the absolute pressure in the water pipe is 26.4 psia.
Discussion Note that jumping horizontally from one tube to the next and realizing that pressure remains the same in the
same fluid simplifies the analysis greatly.
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-37
2-86 A gasoline line is connected to a pressure gage through a double-U manometer. For a given reading of the pressure
gage, the gage pressure of the gasoline line is to be determined.
Pgage = 370 kPa
Assumptions 1 All the liquids are incompressible. 2 The effect of air
column on pressure is negligible.
Oil
Properties The specific gravities of oil, mercury, and gasoline are
given to be 0.79, 13.6, and 0.70, respectively. We take the density of
water to be ๏ฒw = 1000 kg/m3.
45 cm
Gasoline
Analysis Starting with the pressure indicated by the pressure gage and
moving along the tube by adding (as we go down) or subtracting (as
Air
we go up) the ๏ฒgh terms until we reach the gasoline pipe, and setting
22 cm
the result equal to Pgasoline gives
50 cm
Pgage ๏ญ ๏ฒ w ghw ๏ซ ๏ฒ oil ghoil ๏ญ ๏ฒ Hg ghHg ๏ญ ๏ฒ gasoline ghgasoline ๏ฝ Pgasoline
10 cm
Rearranging,
Pgasoline ๏ฝ Pgage ๏ญ ๏ฒ w g (hw ๏ญ SG oil hoil ๏ซ SG Hg hHg ๏ซ SG gasoline hgasoline )
Water
Substituting,
Mercury
Pgasoline ๏ฝ 370 kPa – (1000 kg/m 3 )(9.81 m/s 2 )[(0.45 m) ๏ญ 0.79(0.5 m) ๏ซ 13.6(0.1 m) ๏ซ 0.70(0.22 m)]
๏ฆ
๏ถ๏ฆ 1 kPa ๏ถ
1 kN
๏ท๏ง
๏ด ๏ง๏ง
๏ท
2 ๏ท
2
๏จ 1000 kg ๏ m/s ๏ธ๏จ 1 kN/m ๏ธ
๏ฝ 354.6 kPa
Therefore, the pressure in the gasoline pipe is 15.4 kPa lower than the pressure reading of the pressure gage.
Discussion Note that sometimes the use of specific gravity offers great convenience in the solution of problems that involve
several fluids.
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.
2-38
2-87 A gasoline line is connected to a pressure gage through a
double-U manometer. For a given reading of the pressure gage, the
gage pressure of the gasoline line is to be determined.
Assumptions 1 All the liquids are incompressible. 2 The effect of
air column on pressure is negligible.
Properties The specific gravities of oil, mercury, and gasoline are
given to be 0.79, 13.6, and 0.70, respectively. We take the density
of water to be ๏ฒw = 1000 kg/m3.
Analysis Starting with the pressure indicated by the pressure gage
and moving along the tube by adding (as we go down) or
subtracting (as we go up) the ๏ฒgh terms until we reach the
gasoline pipe, and setting the result equal to Pgasoline gives
Pgage ๏ญ ๏ฒ w ghw ๏ซ ๏ฒ oil ghoil ๏ญ ๏ฒ Hg ghHg ๏ญ ๏ฒ gasoline ghgasoline ๏ฝ Pgasoline
Pgage = 180 kPa
Oil
45 cm
Gasoline
Air
22 cm
50 cm
10 cm
Water
Rearranging,
Pgasoline ๏ฝ Pgage ๏ญ ๏ฒ w g (hw ๏ญ SG oil hoil ๏ซ SG Hg hHg ๏ซ SG gasoline hgasoline )
Mercury
Substituting,
Pgasoline ๏ฝ 180 kPa – (1000 kg/m 3 )(9.807 m/s 2 )[(0.45 m) ๏ญ 0.79(0.5 m) ๏ซ 13.6(0.1 m) ๏ซ 0.70(0.22 m)]
๏ฆ
๏ถ๏ฆ 1 kPa ๏ถ
1 kN
๏ท
๏ด๏ง
๏ง 1000 kg ๏ m/s 2 ๏ท๏ง๏จ 1 kN/m 2 ๏ท๏ธ
๏จ
๏ธ
๏ฝ 164.6 kPa
Therefore, the pressure in the gasoline pipe is 15.4 kPa lower than the pressure reading of the pressure gage.
Discussion Note that sometimes the use of specific gravity offers great convenience in the solution of problems that involve
several fluids.
2-88 The average atmospheric pressure is given as Patm ๏ฝ 101.325(1 ๏ญ 0.02256z )5.256 where z is the altitude in km. The
atmospheric pressures at various locations are to be determined.
Analysis The atmospheric pressures at various locations are obtained by substituting the altitude z values in km into the
relation
Patm ๏ฝ 101325
. (1 ๏ญ 0.02256z)5.256
Atlanta:
(z = 0.306 km): Patm = 101.325(1 – 0.02256๏ด0.306)5.256 = 97.7 kPa
Denver:
(z = 1.610 km): Patm = 101.325(1 – 0.02256๏ด1.610)5.256 = 83.4 kPa
M. City:
(z = 2.309 km): Patm = 101.325(1 – 0.02256๏ด2.309)5.256 = 76.5 kPa
Mt. Ev.:
(z = 8.848 km): Patm = 101.325(1 – 0.02256๏ด8.848)5.256 = 31.4 kPa
2-89 Design and Essay Problems
๏จ๏ง
PROPRIETARY MATERIAL. ยฉ 2017 McGraw-Hill Education. Limited distribution permitted only to teachers and educators for course preparation. If
you are a student using this Manual, you are using it without permission.

## Document Preview (38 of 1792 Pages)

You are viewing preview pages of the document. Purchase to get full access instantly.

-37%

### Solution Manual For Fundamentals of Thermal-Fluid Sciences, 5th Edition

$18.99 ~~$29.99~~Save:$11.00(37%)

24/7 Live Chat

Instant Download

100% Confidential

Store

##### Harper Davis

0 (0 Reviews)

## Best Selling

The World Of Customer Service, 3rd Edition Test Bank

$18.99 ~~$29.99~~Save:$11.00(37%)

Chemistry: Principles And Reactions, 7th Edition Test Bank

$18.99 ~~$29.99~~Save:$11.00(37%)

Test Bank for Strategies For Reading Assessment And Instruction: Helping Every Child Succeed, 6th Edition

$18.99 ~~$29.99~~Save:$11.00(37%)

Test Bank for Hospitality Facilities Management and Design, 4th Edition

$18.99 ~~$29.99~~Save:$11.00(37%)

Data Structures and Other Objects Using C++ 4th Edition Solution Manual

$18.99 ~~$29.99~~Save:$11.00(37%)

2023-2024 ATI Pediatrics Proctored Exam with Answers (139 Solved Questions)

$18.99 ~~$29.99~~Save:$11.00(37%)